BenchOhm

Resistor Color Code Calculator

Read the bands from the crowded end: two or three digit bands, then a multiplier, then tolerance. Yellow-violet-red-gold is 4, 7 and ×100 = 4.7 kΩ ±5% (anything from 4.465 to 4.935 kΩ is in spec).

Colors to value

4.7 kΩ

Tolerance
±5%
Range
4.465 kΩ to 4.935 kΩ
Tempco
not marked
Standard series
E6 (also in E12 and E24)
Read backwards this is gold-red-violet-yellow, which is impossible (gold cannot be a digit), so the direction is certain.

Value to colors

RedRedRedGold

2.2 kΩ is in E6, so it is stocked in every resistor kit.

Math runs in your browser; nothing is sent anywhere. Formula and sources: methodology.

How to read resistor color bands

Hold the resistor so the bands bunched toward one end are on your left. The lone band on the right, separated by a wider gap, is the tolerance band and is always read last. Then:

  1. Digit bands. A 3- or 4-band resistor has two digit bands; a 5- or 6-band precision part has three. Black is 0, brown 1, red 2, and so on up to white 9.
  2. Multiplier. The next band says how many zeros to add, or which power of ten to multiply by. Red adds two zeros (×100), orange three (×1,000). Gold and silver shrink the value: ×0.1 and ×0.01, which is how sub-10-ohm parts are marked.
  3. Tolerance. Gold is ±5%, silver ±10%, brown ±1%, red ±2%. No band at all, as on old 3-band parts, means ±20%.
  4. Tempco (6 bands only). The sixth band gives the temperature coefficient: how many parts per million the resistance drifts per degree. Brown is 100 ppm/K, red 50, yellow 25.

R = (digits) × 10multiplier    Rmin, Rmax = R × (1 ∓ tolerance)

Worked example: orange, orange, black, black, brown on a blue-bodied metal film resistor. Five bands means three digits: 3, 3, 0. The multiplier is black (×1), so the value is 330 Ω, and brown sets the tolerance at ±1%. The same 330 Ω on a 4-band carbon resistor would be orange, orange, brown, gold.

Resistor color code chart

All twelve colors and what each one means in every band position. Digits and multipliers are universal; the tolerance and tempco columns follow IEC 60062:2016.

Pink (×0.001) is a newer multiplier from IEC 60062:2016 that is rarely seen on real parts. Some older charts and datasheets give grey as ±0.05%; under the 2016 standard grey is ±0.01%.
ColorDigitMultiplierToleranceTempco
Black0×1—250 ppm/K
Brown1×10±1%100 ppm/K
Red2×100±2%50 ppm/K
Orange3×1 k±0.05%15 ppm/K
Yellow4×10 k±0.02%25 ppm/K
Green5×100 k±0.5%20 ppm/K
Blue6×1 M±0.25%10 ppm/K
Violet7×10 M±0.1%5 ppm/K
Grey8×100 M±0.01%1 ppm/K
White9×1 G——
Gold—×100 m±5%—
Silver—×10 m±10%—
None——±20%—

A memory aid for the digit order, black to white: "Bench Builders Rarely Order Yellow Green Boards; Very Good Wiring Gets Soldered". The last two words stand for gold and silver. Any phrase works as long as the initials follow B-B-R-O-Y-G-B-V-G-W.

Common resistor values and their colors

The values that turn up most in kits, Arduino tutorials and LED builds. Four-band codes are for 5% carbon or metal film parts with a gold band; five-band codes are for 1% parts with a brown band.

Colors are listed without the tolerance band. A 220 Ω part is the usual series resistor for an LED on 5 V; 10 kΩ is the usual pull-up.
Value4-band (±5%)5-band (±1%)
10 Ω brown-black-black brown-black-black-gold
47 Ω yellow-violet-black yellow-violet-black-gold
100 Ω brown-black-brown brown-black-black-black
220 Ω red-red-brown red-red-black-black
330 Ω orange-orange-brown orange-orange-black-black
470 Ω yellow-violet-brown yellow-violet-black-black
680 Ω blue-grey-brown blue-grey-black-black
1 kΩ brown-black-red brown-black-black-brown
2.2 kΩ red-red-red red-red-black-brown
4.7 kΩ yellow-violet-red yellow-violet-black-brown
10 kΩ brown-black-orange brown-black-black-red
22 kΩ red-red-orange red-red-black-red
47 kΩ yellow-violet-orange yellow-violet-black-red
100 kΩ brown-black-yellow brown-black-black-orange
1 MΩ brown-black-green brown-black-black-yellow

Is the reading backwards? The direction check

Charts never tell you what to do when the gap is too small to see, which is common on cheap 1% metal film resistors with five bands. Our calculator decodes the bands in the opposite order as well. If that reverse reading puts gold or silver in a digit position, it is impossible and the direction is settled. If it decodes, the calculator checks whether the reversed value is a real member of the series that its tolerance implies (E24 for 5%, E96 for 1%). Manufacturers only make standard values, so a reverse reading that lands outside the series is almost certainly wrong.

When both readings are standard values, measure the part with a multimeter before you solder it.
BandsRead left to rightRead right to leftReverse is a standard value?
1 kΩ ±1%110 Ω ±1%yes (E96)
15 kΩ ±1%12 MΩ ±1%no
2.2 kΩ ±1%11 kΩ ±2%yes (E48)

The first row is the classic trap: a 1 kΩ 1% resistor that reads as 110 Ω from the other side, and 110 Ω happens to be a real E96 value. Here the only reliable fix is a meter.

4-band vs 5-band vs 6-band resistors

Why some values do not exist: E-series

Resistors are made in preferred-number series defined by IEC 60063. Each series spaces values evenly on a logarithmic scale so that the tolerance bands of neighbors just about touch. E12 has 12 values per decade for 10% parts, E24 has 24 for 5%, E96 has 96 for 1%. That is why you can buy 4.7k and 5.1k but not 5k. When you type a value into the value to colors tool, it reports which series contains it, or the nearest standard part if none does. If no single part is close enough, two resistors in parallel usually are: see pairs of standard values.

Zero-ohm resistors and SMD codes

A single black band marks a zero-ohm link, used as a jumper on boards that are assembled by machine. Surface-mount resistors are too small for bands and carry a printed number instead: three digits for 5% parts (103 = 10 × 10³ = 10 kΩ), four digits or the EIA-96 letter code for 1% parts. An SMD code reader is planned for this site.

Where the color code stops working

Heat changes paint. A resistor that has run hot can turn red into brown and orange into something closer to red, so a value that looks one band off from what the circuit needs probably is. Some military and high-voltage parts also use a fifth band for failure rate instead of a third digit. When the reading and the circuit disagree, trust the multimeter: measure out of circuit, because parallel paths on a board pull the reading down. For the current and power the resistor actually sees, use the Ohm's law calculator.

Questions people ask

Which end of a resistor do I start reading from?

Start from the end where the bands are crowded together. The tolerance band (usually gold, silver or brown) sits apart from the others with a wider gap, and it is read last. If you cannot tell, enter the bands in both orders: our calculator reads them backwards too and tells you whether the reverse reading is even a real value.

What color code is a 1k ohm resistor?

Brown, black, red, then the tolerance band: 1, 0 and ×100 gives 1,000 Ω. On a 5-band precision part it is brown, black, black, brown, brown (100 × 10 = 1,000 Ω, ±1%).

What is the color code for a 10k resistor?

Brown, black, orange for 4 bands (10 × 1,000). On 5 bands it is brown, black, black, red, followed by the tolerance color.

What does a gold band mean on a resistor?

In the last position gold means ±5% tolerance. In the multiplier position (third band of four) gold means ×0.1, so green, blue, gold is 5.6 Ω.

Why does my 5-band resistor decode to the wrong value?

Usually because it was read as a 4-band part. On five bands the third band is a digit, not the multiplier: brown, black, black, brown, brown is 100 × 10 = 1 kΩ. Read as four bands, the black third band becomes a ×1 multiplier and you get 10 Ω. Count the bands first, and set the calculator to match.

What is a resistor with one black band?

A zero-ohm link: a jumper in a resistor body so that a pick-and-place machine or a board layout can treat it like any other part.

Why can I not buy a 5k resistor?

Resistors come in standard value series. In E24 (the 5% range) the values between 4.7k and 5.6k are 5.1k only, so a 5k part does not exist there. The calculator shows the nearest standard value, or you can combine two parts on our parallel resistor calculator.